Note that BOOT0 announces itself. This would indicate that this card is set up using the legacy method that involves using the allwinner binary blob "boot0.img" and the scheme that goes with it (see u-boot-2017.05/board/sunxi/README.pine64).
HELLO! BOOT0 is starting! boot0 commit : 8 boot0 version : 4.0 set pll start set pll end rtc[0] value = 0x00000000 rtc[1] value = 0x00000000 rtc[2] value = 0x00000000 rtc[3] value = 0x00000000 rtc[4] value = 0x00000000 rtc[5] value = 0x00000000 DRAM BOOT DRIVE INFO: V0.6 the chip id is 0x00000001 the chip id is 0x00000001 the chip id is 0x00000001 the chip id is 0x00000001 the chip id is 0x00000001 axp not exist DRAM CLK =672 MHZ DRAM Type =3 (2:DDR2,3:DDR3,6:LPDDR2,7:LPDDR3) DRAM zq value: 0x003b3bf9 DRAM SIZE =1024 M DRAM simple test OK. dram size =1024 card no is 0 sdcard 0 line count 4 [mmc]: mmc driver ver 2016-03-15 20:40 [mmc]: sdc0 spd mode error, 2 [mmc]: Wrong media type 0x00000000 [mmc]: ***Try SD card 0*** [mmc]: HSSDR52/SDR25 4 bit [mmc]: 50000000 Hz [mmc]: 7580 MB [mmc]: ***SD/MMC 0 init OK!!!*** sum=710a857c src_sum=710a857c read boot-pkg from emmc 32800 sector Succeed in loading uboot from sdmmc flash. Entry_name = u-boot Entry_name = monitor Entry_name = scp set arisc reset to de-assert state Ready to disable icache. �INFO: Configuring SPC Controller NOTICE: BL3-1: v1.0(debug):3ffd944 NOTICE: BL3-1: Built : 11:09:10, Aug 30 2016 NOTICE: BL3-1 commit: 3ffd9442d4769d7fc0002770e3b69b55150a288e INFO: BL3-1: Initializing runtime services ERROR: Error initializing runtime service tspd_fast INFO: BL3-1: Preparing for EL3 exit to normal world INFO: BL3-1: Next image address = 0x4a000000 INFO: BL3-1: Next image spsr = 0x1d3 U-Boot 2014.07 (Nov 09 2016 - 15:49:10) Allwinner Technology uboot commit : 8 secure enable bit: 0 i2c: secure monitor exist [ 0.743]pmbus: ready u0:48105000 [ 0.747][ARISC] :arisc initialize [ 0.777][ARISC] :arisc para ok [SCP] :sunxi-arisc driver begin startup 2 [SCP] :arisc version: [sun8iw5_v0.03.00-244-gb750b8e] [SCP] :sunxi-arisc driver v1.20 is starting [ 0.792][ARISC] :sunxi-arisc driver startup succeeded axp: get node[charger0] error [SCP ERROR] :message process error [SCP ERROR] :message addr : 48105080 [SCP ERROR] :message state : 5 [SCP ERROR] :message attr : 2 [SCP ERROR] :message type : 80 [SCP ERROR] :message result : f3 [SCP WARING] :callback not install [SCP ERROR] :arisc twi read pmu reg 0x3 err probe axp806 failed axp_probe error [ 0.974]PMU: cpux 1008 Mhz,AXI=336 Mhz PLL6=600 Mhz,AHB1=200 Mhz, APB1=100Mhz MBus=400Mhz run key detect no key found no uart input DRAM: 1 GiB fdt addr: 0x76e9f0e0 Relocation Offset is: 35ef2000 axp: get node[charger0] error In: serial Out: serial Err: serial gic: sec monitor mode [box standby] read rtc = 0x0 [box standby] start_type = 0x1 [box standby] to kernel boot_init_gpio used ir boot recovery not used workmode = 0,storage type = 1 [ 1.178]MMC: 0 [mmc]: mmc driver ver 2016-05-20 17:18:00-test0 [mmc]: get card2_boot_para:sdc_ex_dly_used 0 [mmc]: no mmc-hs400-1_8v! [mmc]: no mmc-hs200-1_8v! [mmc]: no mmc-ddr-1_8v! [mmc]: delete max-frequency from dtb SUNXI SD/MMC: 0 [mmc]: 50 MHz... [mmc]: sample: 63 - 158(ps) [mmc]: 100 MHz... [mmc]: sample: 32 - 156(ps) [mmc]: 200 MHz... [mmc]: sample: 16 - 156(ps) [mmc]: media type 0x0 [mmc]: Wrong media type 0x0 [mmc]: ************Try SD card 0************ [mmc]: host caps: 0x27 [mmc]: MID 03 PSN b9a71076 [mmc]: PNM SL08G -- 0x53-4c-30-38-47 [mmc]: PRV 8.0 [mmc]: MDT m-8 y-2016 [mmc]: speed mode : HSSDR52/SDR25 [mmc]: clock : 50000000 Hz [mmc]: bus_width : 4 bit [mmc]: user capacity : 7580 MB [mmc]: ************SD/MMC 0 init OK!!!************ [mmc]: erase_grp_size : 0x1WrBlk*0x200=0x200 Byte [mmc]: secure_feature : 0x0 [mmc]: secure_removal_type : 0x0 [ 1.395]sunxi flash init ok [ 1.410]start drv_disp_init tv_init: tv_probe:000 no report hpd work,you need support the switch class! screen 0 don't support TV! tv_init: fetch tv1 err. drv_disp_init finish hdcp is closed by sys config. no the part:Reserve0 hpd_dev_num=2, id of def_output_dev is 0 hdmi hpd out, force open? fdt_setprop_u32 disp.init_disp(0x20b0404) code:fb_id=0, size=3686400, gd->ram_size=1073741824, SUNXI_DISPLAY_FRAME_BUFFER_SIZE=16777216 [ 1.982]end PowerBus = 0( 2:vBus 3:acBus other: not exist) no battery, limit to dc no battery exist sunxi_bmp_logo_display [boot disp] can not find the partition Reserve0 bmp_name=bootlogo.bmp ** Bad device size - sunxi_flash 0 ** sunxi bmp info error : unable to open logo file bootlogo.bmp fail to find part named env Using default environment --------fastboot partitions-------- mbr not exist base bootcmd=run mmcbootcmd bootcmd set setargs_mmc no misc partition is found to be run cmd=run mmcbootcmd cann't get the boot_base from the env read item0 copy0 Item0 (Map) magic is bad the secure storage item0 copy0 is bad read item0 copy1 Item0 (Map) magic is bad the secure storage item0 copy0 == copy1, the data is good the secure storage map is empty check user data form private the private part isn't exist update dtb dram start update dtb dram end serial is: 44005035c120103e078c [ 2.150]inter uboot shell Hit any key to stop autoboot: 0 sunxi#
Tom's electronics pages / [email protected]